2007-PRESENT, MERCEDES SPRINTER 4X4, BOTTLE JACK USAGE
- Please refer to your owner’s manual for bottle jack location and function
- This blog post demonstrates the functionality of the OEM bottle jack on a 2015 NCV3 4x4 Sprinter with the Van Compass 2” Striker Lift kit and 35” tires.
The point of this blog post is to show how to safely use the OEM bottle jack equipped with the NCV3 / VS30 Sprinter van platforms. We often get a lot of inquiries and questions from our customers regarding what kind of jack they should buy to lift their vehicle up should they need to perform a tire change while out exploring off the grid. Hi-lift? Air Jack? Floor jack? Scissor Jack? The simple answer we tell them is none of those are necessary as the factory bottle jack is actually a quality jack that is more than capable of safely lifting the vehicle.
We are not going to show you how the jack works. For that, refer to your owner’s manual or to the image instructions printed on the bottle jack itself. This is simply meant to be a guide on the bottle jack’s use and what we at Van Compass do to change a flat on our vehicles outfitted for backcountry travel.
The Mercedes sprinter actually has built in jacking points on the chassis designed to take the load from the bottle jack so it can be lifted safely. The rear jacking saddles can be seen in the image below.
Front jacking saddles are similarly shaped and are located just forward of the front mounting bolt of the suspension sub-frame.
However, once a van is fitted with larger tires and a lift kit, those jacking points are often too high for the factory bottle jack to reach. Furthermore, if it does reach, the jack tends to be at it’s upper limit of safe use which makes it a bit more unstable. So here’s what you can do to safely lift your Sprinter with the OEM bottle jack should you need to change a tire out on the trail.
The rear is very simple and straight forward. Position the bottle jack under the axle, outboard of the lower shock mount and directly under the leaf spring perch. This is the perfect position to safely raise one side of the vehicle to perform a tire change. Directly under the leaf spring perch is exactly where the weight of the chassis is carried on the rear axle.
Lifting the front of the van can be a bit more of a challenge, but is still very doable with the factory bottle jack. There are actually a couple of good locations to lift the vehicle from. If you have a Van Compass skidplate system you can position it under the skidplate, directly between the countersunk center mounting holes. However we do suggest using a piece of wood between the skidplate and bottle jack as to not deform the skidplate slightly.
Another front lifting option is the large vertical mounting bolt for the lower spring plate. We tend to use this method more as it lifts one side at a time as opposed to the entire front of the vehicle at once. Center the jack under the large bolt denoted below.
This mounting bolt is loaded directly into the strongest part of the suspension subframe where the lower control arm attaches. Again, use this point to lift the vehicle just to the point of getting the front tire off the ground.
Now for more stability and height when on un-even terrain or soft soil, a very simple upgrade to make the OEM bottle jack work even better is to purchase a Hi-Lift jack base: https://hi-lift.com/accessories/off-road-base/
With just a slight modification, the jack will fit great in the hi-lift base and provide for a much more stable platform in the dirt.
Hopefully this helps people venture of the grid with a bit more confidence. Save the money you were going to spend on a new jack and use it to go buy some diesel. Get out there and have fun exploring with your Sprinter van, we’ll see you out there.
Suspension offerings for the 4x4 Sprinter by Van Compass.
Add protection and peace of mind while exploring in the back country with the Van Compass rear differential skid plate. Loss of gear oil due to a cracked housing or leaking cover can be catastrophic to the rear differential. This skid plate protects the driveshaft u-joints, cast iron differential center section and lower portion of the thin sheet metal differential cover. Constructed from 3/16" steel and powder coated for corrosion resistance to provide a strong, smooth surface to slide over obstacles on the trail. The skid system bolts on in minutes with simple hand tools. Detailed instructions and all necessary hardware is included. Gear oil changes can still easily be performed without skid plate removal.
*COMPATIBLE WITH 2500 MODELS ONLY
The bolt-on Striker 4x4 Sprinter 2.0” suspension lift system provides clearance for larger tires and offers additional ground clearance under the van. Additional traction from larger tires and ground clearance helps to avoid obstacles on the trail to your remote campsite.
The Striker system retains the stock vehicle suspension geometry, payload rating and ride quality. All of the suspension lift system components are constructed of high quality materials here in the USA and are powder coated for durability and corrosion resistance.
With this lift kit, 315/75/16 (35”) tires can be fitted with the following conditions met:
- Removal of the front mudflaps
- Slight trimming of the rear of the front fender
- Trimming of the front bumper and front inner fender well liner.
- Minimum of a 9/16” (14mm) wheel spacer be installed on factory steel wheels with 54mm of offset or any other wheel that has comparable offset. This is for tire clearance between the inside of the tire and the strut and rear inner fender. ** Sold separately
- Note; this could be omitted with an additional 9/16” (14mm) offset and aftermarket wheels.
Van Compass Mercedes Sprinter on-board air system mount and installation